[Tutorial] Nora PC2 mod

pic
20,5 centimeters

About 17,5 grams

This tutorial is from the >Nora blog< a JeB PSer

Stuff :

– 1 Tombow Playcolor 2 (Barrel, cap w/o clip) ;
– 2 Pentel ColorTwin (Caps), here I am using ACT caps but Nora uses CT ;
– 2 Pilot Airblanc (Grips) ;
– 1 or 2 Ohto Needle Point (Grips) ;
– 1 or 2 Pilot Dr.grip (Grip-s) ;
– 2 Uniball Signo (Tips) ;
– 1 Random thin grip. Nora thinks it’s from Zebra hyperjell.

Tutorial :

1- Empty your PC2 and keep only the barrel and cap without clip
12-Cut your airblanc grips at 9mm from the lip
23- Cut your Needle point grip for 13mm (chose the side)
34- Cut your DGG for 25mm (the half of one grip)
45- Cut 2 blocks of the thin grip of 10mm
56- Put grips on this order :
Above the CT cap : airblanc > needle point > DGG
Put Signo tip into the thin grip and put it into the top of CT cap.
67- Put caps on the barrel and check the COG. 🙂

A short video from Nora with this mod :

[Tutorial] Menowa* KT

menowakt
20,5 centimeters for 18 grams

Hello 🙂

I will explain you how to make the Menowa* KT. I found the tutorial on his blog >here<
I don’t understand Japanese. If you see I did errors, don’t hesitate to tell me on comments below, thanks 🙂

Stuff needed :
0– 1 Crayola Supertip (Barrel) ;
– 2 Pentel ColorTwin (2 Caps, 1 Backcap) ;
– 2 Sailor (Grips) ;
– 2 Zebra Airfit (Tips) ;
– 1 or 2 Anyball (Grip : 2×1 blocks) ;
– 2 Zebra Tect (4 plastic rings) Here I’m using regular o-rings ;
Menowa* doesn’t know if the backcap is from PC2 or CT. I will use CT for the tutorial.

Tutorial :

1- Keep 2×1 blocks of Anyball grip. I am using the last from the right on the picture (the bigger one). I don’t know which block Menowa* uses for his mod.
12- Put grips and tip as shown below :
22bis
3- Cut the front of the ST
34- Put Zebra plastic rings on the barrel and the CT backcap.
45- Put the caps on the barrel and check the COG of the mod. 🙂

Video from Menowa* :

Summer PenModding session 2016

Hello guys !

I am making a special article today. I will show you most of the penmods I’ve made this summer. I called it Summer PenModding session 2016 🙂
There are Double Caps, Single Caps, and majority of Japanese. Some French too. I was very productive this summer, hope you will appreciate the stuff ! Enjoy !

The Ajisai DC emboss and SC emboss
The Ajisai DC emboss and SC emboss. Both are really good for spin.

The stats DC : 13,7 grams and 21,2 centimeters.
The stats SC : 15 grams for mine and 20,9 centimeters

 

akashyia-rushon
This Akashiya Rushon is amazing for people who like light penmod. I use Airblanc tips into the caps.

19,5 centimeters for 8,25 grams.
If you like rushon mod but the rushon barrel is too much slippery, you should use an Akashiya barrel, the same for Hibachi mod, or a Fude pen. These markers feel nice 🙂

 

New version of the hibachi?
New version of the hibachi mod ?

I just tell you about the Hibachi. I made this version some weeks ago. I know it’s a different version compared to the Ponkotu’s blog. I think, it may be the real version of the mod. And yes, I found it on the Hibachi’s Blog. I think I will put this tutorial on the blog, soon. 🙂
15,5 grams for about 20 centimeters

 

akiza
Real Akiza g3 from a trade with a japanese pser

But sadly, since I don’t know if Akiza released its tutorial, I can’t gave you any information of this mod, even the mass or the lenght, sorry.
Otherwise, I am really happy to get it.

 

angrykt
Nothing special for this one, I’ve just made again an Angry KT

21,5 centimeters for 18,5 grams
The barrel is a bit slippery but this version of the mod is so cute <3

 

Denial emboss mod
Denial emboss mod

I don’t know if I can release the stuff to make it, because I am not even sure if Denial knows the barrel origin.. If you want to know it, think about a colorful donga barrel sub. 🙂
Caps are made as a regular emboss mod.

 

drbt
Yes, I finally made one ! <3 it’s a Dr.BT, a Menowa*’s mod, in full black ver. 🙂

Mine is 20,5 centimeters for 17 grams. Yup, it’s light for a Dr.KT type. But I don’t like this mod when it’s more than this weight.
I’ve use black Beifa grip instead of Sailor grip and black o-ring (you can find them on my store) instead of zebra Tect ring.
The barrel is not tappered so it’s perfect to put caps above, and the length is 11,3 centimeters (of barrel ofc). It’s from the brand Stalogy and very expensive pen. It’s more expensive than a regular Japanese Dr.grip shaker. 😥

 

everchix
Everchix g3. He made 2 g3 mods, here is one of them. Maybe I will try to make the other 🙂

About 20 centimeters for 16 grams

 

Full black Joshin BS
Full black Joshin BS

20,5 centimeters for 14,6 grams, with black BS barrel

 

Malimo G3 mod, the real version use a black tinted jimnie cap
Malimo G3 mod, the real version use a black tinted jimnie cap

12,5 grams for 19,5 centimeters

 

misag3
The Misa g3 is a good penmod for people who have smalls hands

18,5 centimeters for 16 grams

 

peemaleft
Peemalux is a french mod, the barrel used is called Impega from the brand Lyreco. Only findable in France, I believe.

I really like this mod, 20 centimeters for 15 grams.
The barrel is amazing because it grabs more than a flexgrip ultra barrel (Banz’ mod).
Tornado grips, very light airfits grips.

It’s the version of Leftfinger, a french pser :

 

toropurple
A penmod I bought from an UPSB seller, sparking

And the last mod, a purple Toro mx 😀

Mesi G3 mod V2 tutorial

mesiv2This Mesi G3 mod v2 was made by MJerry. All credits go to him.

 

First JeB penmod tutorial on my website, the Mesi v2 ! I found it on >Mesi’s blog<, so I think it’s the legit one 🙂

12 grams
20 centimeters

  • Stuff needed :
    – 1 Pilot plastic G3 (Backcap, barrel, tip, grip, inktube)
    – 1 Pilot Frixion [ the one with white barrel and tinted cap ] (Cap, rubber grip)
    – 3 Zebra D-1K (Grips) : only findable in Japan, try to trade with JeB people. Otherwise, you can sub it to Anyball grips
    – 1 Metallic Gel (Tip)
    – 1 Zebra Hyperjell (Grip)
    – 1 Sakura BallSign (Backplug)
    – 1 Hybrid Fine / Hybrid Gel Grip (Tip)
    – A small random grip (?)

 

  • Tutorial :

– Cap, part A :

  1. Put G3 backcap and Frixion rubber grip together like below :
    1
    2. Add a G3 4 stripes grip above the step 1. Don’t forget to cut the grip like that :

2

– Cap, Part B :

  1. Empty all the Frixion cap.
  2. Put the BallSign backplug into the top of Frixion cap and cut the backplug until to get that :

2011090620174767fSo, the black part on the top is a small part of BallSign backplug

3. Take the G3 inktube and keep only the grey part :

3

4. Then, put it on the top of Frixion cap :

5

– Cap, part C :

  1. Put the step 1 and the Hyperjell grip together like that :

6

2. Put this package grips into Frixion cap

7

– Barrel, front part :

1. Prepare the G3 front as all G3 mod (remove grip, the 8 small plastic squares and file the ruffle just near the tip)

2. Put G3 tip > Metallic gel tip > HGG tip

8

3. Add D-1K 15 stripes grips on the front : 5 red stripes > 4 black stripes > 6 red stripes

9

4. Add 2 red stripes and 4 black stripes of D-1K on the Frixion cap. (I am not sure about this step)

5. Put an insert into the barrel and put Frixion cap on the back of the G3. You have finished ! 🙂

Short combo with this mod, from Mesi.